 |
Te Connectivity Gray J1939 Male to OBD II SAE J1962 Female Automotive Diagnostic Cable Assembly
Szczegóły Produktu:
Zapłata:
| Minimalne zamówienie: | 5000 |
|---|---|
| Cena: | 100 |
|
Szczegóły informacji |
|||
| Woltaż: | prąd stały 300 V | Opór kontaktowy: | 3,0 oma MAKS |
|---|---|---|---|
| Temperatura pracy: | -20~80°C | Poziom: | 4mm |
| Napięcie pojazdu: | 12 V dla samochodu, 24 V dla pojazdu ciężkiego | Tworzywo: | PA66, powlekany zębami, zgodny z ROHS |
| Typ złącza: | Niemiecka seria HD10 | Temperatura pracy: | -40ºC do +125ºC |
| Odporność na wibracje: | 20 G przy 10 do 2000 Hz | Ocena IP: | IP68 |
| Wodoodporna głębokość: | 1,2 metra przez 24 godziny | Wnęka złącza: | 3, 4, 5, 6, 9 |
| Rozmiar kontaktu: | 16, 4/16, 12 | Długość całkowita A: | 1,609 (40,87) |
| Wysokość całkowita ØB: | 1,069 (27,15) | ||
| Podkreślić: | J1939 to OBD II diagnostic cable,automotive diagnostic cable assembly,J1939 male to J1962 female cable |
||
opis produktu
TE Connectivity J1939 to OBD II Diagnostic Cable Assembly
TE Connectivity Gray J1939 Male to OBD II SAE J1962 Female automotive diagnostic cable assembly designed for heavy-duty vehicle applications.
Key Specifications
- Voltage: DC 300V 5m ohm/10 ms
- Contact Resistance: 3.0 ohm MAX
- 100% Open, Short, Mis-Wire Testing
SAE OBD-II Standards Documentation
- J1708 - Defines serial communications between ECUs on heavy duty vehicles
- J1850 - Defines serial data protocol with VPW/PWM variants
- J1939 - Defines data protocol for heavy duty commercial vehicles
- J1962 - Defines physical connector for OBD-II interface
- J1978 - Defines minimal operating standards for OBD-II scan tools
- J1979 - Defines standards for diagnostic test modes
- J2012 - Defines trouble codes and definitions
- J2178 Series - Defines network message standards and parameters
- J2284-3 - Defines 500 kbit/s CAN Physical and Data link layer
- J2411 - Describes GMLAN protocol for newer GM vehicles
J1962 Connector Specifications
The SAE J1962 specification provides two standardized hardware interfaces - Type A for 12V vehicles and Type B for 24V vehicles. Both feature 16-pin D-shaped connectors with type B having an interrupted groove for compatibility.
Pin Configuration
| Pin Number | Description |
|---|---|
| 1 | Manufacturer Discretionary |
| 2 | SAE J1850 Bus + (VPW / PWM) |
| 3 | Manufacturer Discretionary |
| 4 | Chassis Ground |
| 5 | Signal Ground |
| 6 | CAN High (ISO 15765-4 and SAE J2284) |
| 7 | ISO 9141-2 / ISO 14230-4 K Line |
| 8 | Manufacturer Discretionary |
| 9 | Manufacturer Discretionary |
| 10 | SAE J1850 Bus - (PWM-only) |
| 11 | Manufacturer Discretionary |
| 12 | Manufacturer Discretionary |
| 13 | Manufacturer Discretionary |
| 14 | CAN Low (ISO 15765-4 and SAE J2284) |
| 15 | ISO 9141-2 / ISO 14230-4 L Line (Optional) |
| 16 | Vehicle Battery Power: Type A 12V/4A, Type B 24V/2A |
Technical Specifications
Material: PA66, tinned plated compliant ROHS
Working Temperature: -20°C to 80°C
Over-molding: Customized
Pitch: 4mm
Voltage: 12V for car and 24V for heavy vehicle
DEUTSCH HD10 Series Connector
The HD series features environmentally sealed silicone rubber, thermoplastic cylindrical connectors designed for heavy-duty applications in trucks, buses, cross-country vehicles, cranes, and forklifts. Provides protection against water, dust, oils, fuel, road salt, grease, and contaminants.
Performance Features
- Operating Temperature: -40°C to +125°C
- No cracking, chipping or leaking after 20 test cycles
- Withstands 20 G's vibration at 10-2000Hz for 2 hours
- IP68 rating - waterproof up to 1.2 meters for 24 hours
Dimensional Specifications
| Cavity | Overall Length A | Overall Height ØB | Overall Length C | Overall Height ØD |
|---|---|---|---|---|
| 3 | 1.609 (40.87) | 1.069 (27.15) | 1.639 (41.63) | 0.851 (21.62) |
| 4 | 1.639 (41.63) | 1.595 (40.51) | 1.639 (41.63) | 1.281 (32.54) |
| 5 | 1.609 (40.87) | 1.218 (30.94) | 1.639 (41.63) | 1.001 (25.43) |
| 6 | 1.619 (41.12) | 1.453 (36.91) | 1.639 (41.63) | 1.141 (28.98) |
| 9 | 1.609 (40.87) | 1.593 (40.47) | 1.639 (41.63) | 1.281 (32.54) |
HD10 Series Configuration
| Position | Contact Size | Rear Threads | Plug | Receptacle Inline | Receptacle Flange |
|---|---|---|---|---|---|
| 3 | 16 | no | HD16-3-16S | HD14-3-16P | - |
| 3 | 16 | yes | HD16-3-96S | HD14-3-96P | HD10-3-96P |
| 4 | 4/16 | yes | HD16-4-4S | - | HD10-4-4P |
| 5 | 16 | no | HD16-5-16S | HD14-5-16P | HD10-5-16P |
| 6 | 16 | yes | HD16-6-96S | HD14-6-96P | HD10-6-96P |
| 6 | 12 | yes | HD16-6-12S-B010 | HD14-6-12P | HD10-6-12P |
| 9 | 16 | no | HD16-9-16S | HD14-9-16P | HD10-9-16P |
| 9 | 16 | yes | HD16-9-96S | HD14-9-96P | HD10-9-96P |
| 9 (J1939) | 16 | yes | HD16-9-1939S | HD14-9-1939P | HD10-9-1939P |
Company Profile
- Privately held company, established in 1999
- Sales volume over 16 Million USD since 2017
- OEM & ODM company with 250+ employees
- 7,260 square-meter facility
- Specialized in economical solutions and innovative wire harness design & manufacturing
- IATF16949 (2016) & ISO 9001 (2015) certified
- UL certified supplier with wiring No. E468011 & cable No. E479323
Certifications
Frequently Asked Questions
Can you help with design?
Yes, we are an ODM/OEM company specializing in wire harness & cable assembly since 1999.
When will you start to help design?
We provide initial solution sketches for discussion. After quotation and order placement, we proceed with detailed drawings and client confirmation.
What if quality issues occur?
Our quality and engineering team responds to quality issues within 72 hours, committed to long-term partnerships and superior service.
Do you have standard products to reduce lead time and tooling costs?
Yes, we maintain over 1000 sets of molds, many of which can be used directly for customer projects. With over 20 years of specialization and 5000+ products.
Contact Us
For more information about our TE Connectivity J1939 to OBD II diagnostic cable assemblies and other wire harness solutions, please contact our sales team.
Chcesz dowiedzieć się więcej o tym produkcie